Concrete, Steel And Timber In The Same Building
A building rarely uses one material all the way up. A concrete basement and podium with steel or timber above is a common combination, and it works well, provided the joins between materials are designed as carefully as the materials themselves.
We design the concrete to AS 3600, the steel to AS 4100 and the timber to AS 1720.1, or AS 1684 for house-style framing, and we check each one against the others at every connection. Most of the trouble in a mixed building starts at those connections.
Why mix materials
Concrete suits anything touching the ground, and floors that need mass, stiffness and fire resistance. Steel and timber are lighter, so they suit roofs, long spans and upper levels, where less weight above means smaller columns and footings below.
Shrinkage at the joins
A concrete frame shortens a little as it dries and creeps under load over the years, as covered in [shrinkage and creep in concrete structures](/blog/shrinkage-and-creep-in-concrete-structures). Timber shrinks too, mostly across the grain, as it dries to suit the building.
In a timber frame, the wall plates and floor joists carry load across their grain, so a stack of them shrinks noticeably as it dries, while a concrete lift core or a steel column beside it doesn't. Fix the two rigidly together and something has to give, such as a cracked lining, a pipe pulled at a fitting, or a step at the junction between a timber floor and the core.
The answer is to let them slide past each other, with slotted connections, gaps at the junction, and fixings that hold sideways without locking the vertical movement.
Steel and timber on a concrete slab
Every steel column and timber wall standing on concrete needs a fixing that holds it down against wind uplift and holds it in place sideways. For steel, that is a baseplate and holding-down bolts, set out in [steel baseplates and holding down bolts](/blog/steel-baseplates-and-holding-down-bolts). For timber, it is bolts, rods or brackets anchored into the slab, with the bracing and tie-down principles in [bracing and tie-down in timber framed houses](/blog/bracing-and-tie-down-in-timber-framed-houses).
Edge distance decides a lot. An anchor too close to a slab edge breaks out a cone of concrete before it reaches its rated load, so the slab edge and the fixing get detailed together.
Moisture matters at the same joint. Concrete holds water for a long time after it is poured, and a timber bottom plate sitting straight on it stays damp, so a damp-proof barrier goes between them.
Tolerances
Concrete is built to looser tolerances than fabricated steel. A steel beam made in a workshop to the millimetre has to land on cast-in bolts or a concrete ledge that sits a little out of position, so the connections between the two allow for adjustment, with slotted holes, packers, and grout under baseplates.
Corrosion
Steel fixings in treated timber corrode faster, because the preservative chemicals attack plain steel, so fixings into treated timber are hot-dip galvanised or stainless steel. Steel against damp concrete, or hidden in a wall cavity, needs a coating chosen for that exposure, and different metals touching in the wet are kept apart. The coating options are in [corrosion protection for structural steel](/blog/corrosion-protection-for-structural-steel).
Fire and sound
Fire and acoustic separation change at each junction between materials. A timber floor over a concrete podium relies on its ceilings and linings for its fire rating, and the junction has to keep that rating continuous. The fire engineer and the acoustic consultant set those requirements, and we design the structure around them.
One set of drawings
The risk in a mixed building is the gap between packages. The concrete drawings stop at the slab, the steel shop drawings start at the baseplate, and prefabricated timber frames and trusses come from a supplier's software.
How we approach it
We draw the connections between materials on our own structural set, so nobody on site has to decide who owns a bolt. Every interface gets a detail, a tolerance and a fixing, and our site inspections check them as closely as the members themselves.
Three materials can share a building happily, as long as someone has designed the places where they touch.
ACSES provides structural engineering in concrete, steel and timber across Sydney. Talk to us about a project.
Building Relationships Beyond Structures
Related Articles
Tell us about your project.
We will respond with a clear understanding of how we can assist.
Partner With Us

